how to change laser lens on wii


How to Change the Laser Lens on a Wii

The Nintendo Wii console has been a popular gaming device since its release in 2006. However, like all electronics, it can experience problems over time. One common issue with the Wii is that it may stop reading discs properly. This can be due to a damaged or dirty laser lens. If you find yourself in this situation, worry not! This article will guide you step-by-step through the process of changing the laser lens on your Wii.

Before we start, here are some important things to keep in mind:

- This guide is for the Wii console only, not the Wii U.

- It's important to use caution throughout the process as the Wii console is delicate.

- If your Wii is still under warranty, it's best to contact Nintendo to avoid voiding your warranty.

- You will require some tools and a replacement laser lens, which you can purchase online.

With that said, let's dive in!

Tools required:

- Tri-wing screwdriver

- Phillips screwdriver

- Isopropyl alcohol

- A new laser lens

Step 1: Remove the Wii's casing

The first step in changing the laser lens is to remove the Wii's casing. Here's how to do it:

- Unplug all cables from the console.

- Remove the battery cover on the bottom of the Wii remote and take out the batteries.

- Turn the console upside down.

- Detach the four rubber feet on the bottom of the console by gently prying them off with your fingernail or a small flathead screwdriver.

- Remove the four tri-wing screws underneath the rubber feet.

- Flip the console over and remove the two Phillips screws on the back of the Wii.

- Gently remove the plastic casing from the Wii, being careful not to damage any of the internal components.

Step 2: Access the laser lens

After removing the Wii's casing, you will need to access the laser lens. Here's how to do it:

- Locate the DVD drive on the Wii's motherboard—it's the component with the spinning disc.

- Carefully lift up the two clips on the DVD drive and pull the drive out of the motherboard.

- Unscrew the three Phillips screws located towards the middle of the DVD drive's board.

- Gently lift the board away from the rest of the drive to reveal the laser lens.

Step 3: Remove the old laser lens

Once you have access to the laser lens, it's time to remove the old one. Here's how to do it:

- Locate the two small clips on the sides of the laser lens.

- Gently lift the clips with a small flathead screwdriver, being careful not to damage the clips.

- Carefully remove the old laser lens from the DVD drive board.

Step 4: Install the new laser lens

Now it's time to install the new laser lens. Here's how to do it:

- Ensure that the replacement lens is the correct model before starting.

- Align the new laser lens with the two clips on the DVD drive board.

- Push down gently on the lens until it snaps into place.

Step 5: Reassemble the Wii

Finally, it's time to reassemble the Wii. Here's how to do it:

- Reattach the DVD drive to the Wii's motherboard.

- Screw the three Phillips screws back in place.

- Reattach the plastic casing to the Wii.

- Screw the two Phillips screws on the back of the Wii back in place.

- Replace the rubber feet on the bottom of the console.

- Put the batteries back in your Wii remote and reattach the battery cover.

- Plug in all the cables and turn on the console.


In summary, changing the laser lens on a Wii is not as difficult as it may seem. With a bit of caution and attention to detail, you can fix this common issue on your own. Just remember to have the required tools and a replacement laser lens before starting. Now that you know how to change the laser lens on a Wii, you can get back to enjoying your favorite games!


Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
Current language:English